FIRE DETECTION SYSTEMS | 4WIRE CONVENTIONAL SYSTEMS | 47 t: 0845 884 7000 | f: 0845 884 6000 | w: www.channelsafety.co.uk | @channelsafety | EDITION 7 Kentec Sigma CP conventional Range  EN54Third Party Approved Sigma CP The Sigma CP range consists of a series of conventional fire alarm control panels designed in accordance with European standards BS EN54-2 and BS EN54-4 Fire Detection and Fire Alarm systems - Control and Indicating Equipment. The range consists of 2, 4 and 8 zone control panels. All control panels are available in two versions: Compatible with Apollo Series 65 & C-Tec Active detector ranges (see pages 46,48 & 49 ) Sigma K11 range in which detectors and call points are wired on separate circuits to sounders (two sounder circuits are provided).Sigma T11 range in which detectors, call points and sounders are wired to the same pair of cables. Commonly referred to as a two-wire system are available to order. (Alarmsense devices see pages 50-51) Wiring sounders to the detection circuits eliminates the need to install sounder circuit cables and also offers the ability to provide zoned or two stage sounder operation All control panels have an integral, mains powered battery charger and power supply designed in accordance with the requirements of BS EN54-4. PRODUCT FEATURES • Fully certified to BS EN54-2 and BS EN54-4 2-wire and standard versions in 2, 4 or 8 zones • Compatible for use on BS5839: Part 1: 2002 installations • 2-wire repeaters and ancillary boards • Fully programmable using simple menu options • Adjustable sounder delay time • Sounder configuration options • Zonal sounder delay detectors only • Zonal sounder delay call points only • Coincidence input selection • I.S Barrier selection by zone • Short circuit fire by zone • Non latching zones • Silent zones • Zone input delay • General panel configuration • Simple, single board construction • Installer friendly • Compatible with wide range of detection devices • Two monitored sounder outputs • 3 Amp power supply • Auxiliary power output • Also available is a range of Ancillary Cards compatible with all • Sigma CP Models. Up to 7 Cards of each model can be fitted • to each Sigma CP Control Panel & Sigma CPR Repeater Panel • Ranges. These include: • Sigma Ancillary Board (K580) operating software version • V2.0 or above. See DS39 for more details. • Sigma Sounder Board (K461) operating software version V3.0 PRODUCT CODE DESCRIPTION F/KL11020M2 Sigma CP Conventional Panel 2 Zones: Surface + LCMU- Conventional F/KL11040M2 Sigma CP Conventional Panel 4 Zones: Surface + LCMU- Conventional F/KL11080M2 Sigma CP Conventional Panel 8 Zones: Surface + LCMU- Conventional F/KA11020M2 Sigma CPA Alarmsense Conventional Panel, 2 Zones: Surface- 2 Wire F/KA11040M2 Sigma CPA Alarmsense Conventional Panel, 4 Zones: Surface- 2 Wire F/KA11080M2 Sigma CPA Alarmsense Conventional Panel, 8 Zones: Surface- 2 Wire B/BATT/12V/7AH/SLA 12 Volt 7Ah Sealed Lead acid battery (1 block) 2 required per panel REPEATERS F/E01020L2 Sigma CP-R Conventional Repeater Panel, 24V low profile enclosure, 2 Zones: Surface F/E01040L2 Sigma CP-R Conventional Repeater Panel, 24V low profile enclosure, 4 Zones: Surface F/E01080L2 Sigma CP-R Conventional Repeater Panel, 24V low profile enclosure, 8 Zones: Surface F/K01020M2 Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure, 2 Zone: Surface F/K01040M2 Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure, 4 Zone: Surface F/K01080M2 Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure, 8 Zone: Surface